JavaScript is required to view this page.
Skip to content
Get 2x Free Smart Devices with your HA Yellow Kit + CM4
Get 2x Free Smart Devices with your HA Yellow Kit + CM4

ODROID-H3 / H3+

Original price $161.95 - Original price $206.95
Original price
$161.95
$161.95 - $206.95
Current price $161.95
Availability:
In-Stock
Availability:
In-Stock

ODROID-H3 and H3+ have the same form factor and similar power efficiency as their predecessor, the ODROID-H2+. However, the H3 and H3+ are more powerful, offering higher performance. You’ll need to supply your own memory and storage (check the recommended accessories on this page) — but since the ODROID-H3 family uses the same components commonly found in modern laptops, you should have no trouble finding compatible hardware to fill out your SBC.

ONLY NVMe M.2 SSD ARE COMPATIBLE: PCIe NVMe M.2 SSD

Both models of ODROID-H3 feature two SO-DIMM slots for memory, two SATA ports and one M.2 NVMe slot for storage, two 2.5 GbE ports, two USB 3.0 ports, two USB 2.0 ports and more!

  • ODROID-H3: Intel quad-core Jasper Lake N5105 processor
  • ODROID-H3: Intel quad-core Jasper Lake N6005 processor

Additional items required to operate - see "REQUIRED ITEMS" section below.

KEY FEATURES

  • SoC:
    • H3: Intel Jasper Lake N5105 quad-core processor, base clock of 2.0GHz and boost up to 2.9 GHz
    • H3+: Intel Jasper Lake N6005 quad-core processor, base clock of 2.0GHz and boost up to 3.3 GHz
  • GPU:
    • H3: Intel UHD Graphics 24 EUs Turbo 800MHz
    • H3+: Intel UHD Graphics 32 EUs Turbo 900MHz
  • System Memory – Dual-channel Memory DDR4 PC4-23400 (2933MT/s) supporting up to 64GB RAM in total
  • Storage – M.2 PCIe 3.0 x4 slot for one NVMe storage, 2x SATA 3.0 ports, eMMC flash support
  • Video Output
    • HDMI 2.0 up to 4K (4096×2160) @ 60 Hz
    • DisplayPort 1.2 up to 4K (4096×2160) @ 60 Hz
  • Audio – HDMI, audio jacks for HP, MIC. and S/PDIF
  • Connectivity – Dual 2.5 Gigabit Ethernet (RJ45)
  • Expansion – 24-pin header with I2C, UART (3.3V), USB2.0 and HDMI CEC signals
  • SSE4.2 accelerator (SMM, FPU, NX, MMX, SSE, SSE2, SSE3, SSSE3, SSE4.1, SSE4.2, AES)
  • A configurable Unlimited Performance mode allowing the CPU to run in sustained turbo boost mode
  • Misc – RTC battery (Included)
  • Power Supply – 14V to 20V DC power input
  • Dimensions – 110x110x43mm
  • Weight – About 320 grams with heatsink, two DRAM modules, and M.2 NVMe SSD.

REQUIRED ITEMS (NOT INCLUDED)

  • No power supply included - 15VDC/4A power supply required
  • No RAM pre-installed - DDR4 SODIMM
    • DDR3/DDR5 is not supported
  • No eMMC Module or SSD included 
    • M.2 SATA SSD is not supported (only NVMe SSD)
  • No case included
  • No HDMI cable included - needed to connect to a display device. Recommend HDMI2.0 cable to support 4K output

SPECIFICATIONS

Processor
  • Intel Celeron N5105(H3+: N6005) Processor (10nm, Quad-Core, TDP 10W)
  • H3(N5105): up to 2.9GHz
  • H3+(N6005): up to 3.3GHz
  • 4MB L2 Cache
  • Intel UHD Graphics (24/32 EU up to 900MHz)
Memory
  • 2 x DDR4 1.2V SO-DIMM slots, Dual Channel, up to 2933 MT/s (DDR4-PC23400)
  • Max memory capacity 64GB
  • DDR3/DDR5 are not supported
Storage
  • 1 x eMMC connector (bootable and selectable on BIOS)
  • 2 x SATA3 6Gbps
  • 1 x M.2 slot (PCIe 3.0 x 4, supports NGFF-2280 cards)
  • M.2 SATA SSD is not supported
Networking
  • 2 x GbE LAN ports (RJ45, supports 10/100/1000/2500 Mbps)
  • Realtek RTL8125B
  • Supports Wake-On-Lan
  • LED indicators (Green: Link, Amber: Traffic)
Video
  • 1 x DisplayPort 1.2 (up to 4K@60Hz)
  • 1 x HDMI 2.0 (up to 4K@60Hz)
  • Dual simultaneous display support
Audio
  • 1 x Audio out (3.5mm jack)
  • 1 x Audio in (3.5mm jack)
  • 1 x SPDIF out (ALC1200, HDA codec)
  • * HDMI & DP have audio output too.
External I/O
  • 2 x USB 3.0 Host ports
  • 2 x USB 2.0 Host ports
  • 1 x Peripheral Expansion Header (24-pin, 2.54mm pitch)
  • 1 x DC 5V, 1 x DC 3.3V, 5 x GND
  • 1 x UART (TXD/RXD/RTS/CTS)
  • 2 x I2C (SCL/SDA)
  • 1 x External Power Button
  • HDMI CEC, 5VA+
  • Three USB 2.0 ports
  • All 3.3V I/O signal level
Other Features
  • Passive Heatsink
  • BIOS Backup Battery
  • Maintains system time and BIOS settings
  • Power Button
  • Reset Button
  • System LEDS Indicators:
  • Red (PWR) – Solid light when DC power is supplied
  • Blue (left, SLEEP) – turns off only when the system enters into suspend mode
  • Blue (right, PMIC) – turns on only when the major power rails are working
  • Amber (SATA) – Flashes when SATA data transfers
  • Green (NVMe) – Flashes when NVMe data transfers
  • Active Cooling Fan Connector (12V 4-pin, PWM input + TACHO output)
  • Active Cooling Fan is optional
  • Connector (4-pin, 2.54mm pitch)
Power
  • DC jack: outer (negative) diameter 5.5mm, inner(positive) diameter 2.1mm
  • DC 14V ~ 20V (up to 60W)
  • DC 15V/4A power adapter is recommended if you don’t use two 3.5“ HDDs
  • DC 19V/7A power adapter is recommended if you use two 3.5” HDDs together
  • Power consumption:
  • IDLE: ≃1..9W
  • CPU Stress: ≃15W
  • CPU+GPU Stress: ≃18W
  • Power-off: ≃0.25W
  • Suspend: ≃0.6W
Form Factor 110mm x 110mm x 47mm Approx.

  • A. CPU (Intel Celeron N5105)
  • B. 2 x DDR4 SO-DIMM slots (Dual channel memory support)
  • C. 1 x M.2 PCI Express Module Socket (NGFF-2280)
  • D. 1 x eMMC (Embedded Multimedia-Card) Socket
  • E. 2 x SATA Power Connectors (2.5mm pitch, JST-XH compatible connector)
  • F. 2 x SATA3 6.0 Gb/s Data Connectors
  • G. 1 x DC Power Jack
  • H. 2 x USB 3.0
  • I. 2 x USB 2.0
  • J. 1 x HDMI 2.0
  • K. 1 x DisplayPort 1.2
  • L. 2 x RJ45 Ethernet Ports (10/100/1000/2500)
  • M. 5 x System LED Indicators
  • N. 1 x Peripheral Expansion Header (24-pin)
  • O. 1 x Power Switch
  • P. 1 x Reset Switch
  • Q. 1 x Backup Battery Connector (2-pin)
  • R. 1 x Active Cooling Fan Connector (4-pin)
  • S. 1 x Audio out, 1 x Audio in, 1 x SPDIF out

LINKS

 VIDEOS

x

SKU I0730
Variant: H3

Customer Reviews

Based on 4 reviews
100%
(4)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
C
Cliff Langlois
Slick

First time builder…..20 minutes and success. Very nice.

C
Celtic
Great small factor board

I have this board as a small media NAS running Openmediavault and it’s working great. Board runs cool and everything working well. I am really glad I went this route. So many out there say to buy old hardware but I want new and prefer to build how I want it to be.

C
ChrisJ
ODroid H3: Silent and powerful little board

I replaced an old, loud Dell Vostro Linux box that I was using as a NAS with this little board, the "Type 1" case, and a few other parts. It does exactly what I want, runs everything much faster than the old Dell, takes up very little space, and is completely silent unless the drives are spun up. It's been running for eight months now, and I'm very happy with the purchase.

M
MacH
Odroid H3+ x2

I have 2 H3+ computers. Both are populated with 16gB RAM and 1tB M.2 NVME SSD. One is running Windows 11. The other is running Linux Mint Cinnamon. The Windows machine is an open platform. The Linux machine is in the Odroid case. Both machines have worked PERFECTLY since I installed them. They are fast quiet and are each driving a 27" 1920x1080 60hz monitors. I added a Noctua AF-N8 fan to each. They are silent running and are off about 50% of the time. I have 3 wishes for Odroid. 1. Add a 2nd M.2 NVME socket. 2. Add a M.2 socket for Wifi. 3. Cut a hole in the case to allow the SATA cables to extend below the main card.